OEM plastic product manufacturing service

We are a specialized manufacturer providing precision OEM plastic product manufacturing services for custom plastic parts and functional sub-assemblies. Unlike general traders, we offer comprehensive in-house expertise—from material science and mold design to production, finishing, and secondary assembly—delivering engineered components that meet exact technical and cosmetic requirements.

1. Custom Engineering for plastic Components

We collaborate with you to optimize part design for performance, manufacturability, and cost. Our engineering focus covers all critical structural elements:

Ribs & Bosses: Strategically designed to enhance rigidity without causing sink marks, ensuring strength for mounting and assembly points.

Wall Thickness: Maintained uniformly to facilitate optimal flow of ABS, preventing warpage and internal stresses for dimensional stability.

Draft Angles & Ejection: Carefully calculated to enable smooth part release from the mold, protecting high-gloss or textured surfaces.

Snap-fits, Living Hinges & Ultrasonic Welding Bosses: Integrated into the design to enable secure, post-molding assembly. ABS’s excellent toughness makes it ideal for these interlocking features.

Gating & Flow Analysis: Simulated to place gates in non-critical areas, minimizing visible blemishes and ensuring proper fill of the entire cavity.

2. ABS Material Expertise: Properties & Tailored Applications

ABS (Acrylonitrile Butadiene Styrene) is chosen for its outstanding balance of properties. We guide you in selecting the right grade for your application:

Key Properties: Excellent impact strength and toughness, good dimensional stability, high surface gloss, and innate aesthetic quality. It offers good chemical resistance and is easily modified.

Common Grades & Uses:

General Purpose: For housings, consumer products, and prototypes requiring good strength and finish.

High-Impact: For automotive interior trim, protective covers, and parts requiring enhanced durability.

Heat-Resistant: For components near light sources or in warm environments (e.g., appliance housings, dryer vents).

Platable Grades: Specially formulated for parts requiring chrome-plating or metallization (e.g., automotive grilles, bathroom fixtures).

Flame-Retardant (FR): For electronics enclosures and components that must meet specific safety standards (UL94 HB, V-0, etc.).

Material Comparison: We advise when ABS is optimal versus alternatives. For example, ABS offers better processability and gloss than Polypropylene, greater toughness than Polystyrene, and is more cost-effective than Polycarbonate for many non-transparent applications.

3. The Precision OEM plastic product manufacturing Process & Key Advantages

Our controlled molding process is tailored to unlock the full potential of ABS material, ensuring part consistency and quality.

Process Highlights: Precise temperature control in the barrel and mold is critical for ABS to achieve its signature surface finish. We utilize advanced processing parameters to manage viscosity and cooling rates, optimizing the mechanical properties of the final part.

Primary Advantages of Our ABS Molding Service:

Superior Surface Finish: ABS naturally yields a high-gloss, aesthetically pleasing surface straight from the mold, reducing or eliminating the need for post-processing painting for many applications.

Excellent Dimensional Stability: Parts exhibit minimal shrinkage and warpage, holding tight tolerances crucial for assembly and fit.

High Strength & Durability: The process ensures optimal polymer orientation and packing, resulting in components with reliable impact resistance and structural integrity.

Design Flexibility & Consolidation: Complex geometries, textures, and integrated features can be molded in one shot, reducing the number of parts and assembly steps.

Cost-Effectiveness at Volume: Combined with ABS’s relatively low material cost, an efficient molding process delivers highly reliable parts at a competitive price point for medium to high-volume runs.

4. Our Value: From Component to Sub-Assembly

We go beyond molding individual parts. Our integrated service includes:

Post-Molding Operations: We provide a full range of secondary services such as ultrasonic welding, vibration welding, adhesive bonding, press-fitting of inserts, and simple mechanical assembly.

Finishing Services: Painting, pad printing, laser etching, and assembly for complete, ready-to-install sub-assemblies.

Full-Process Ownership: We manage the entire value chain—from DFM (Design for Manufacturability) and mold fabrication to final inspection and packaging. This ensures accountability, quality control, and seamless production.

Choose us for your ABS components when you require a partner who understands both the material science and the precision manufacturing required to produce durable, high-quality, and cost-effective parts. We deliver not just molded plastic, but engineered solutions that integrate seamlessly into your final product.

Mold Preparation

Mold Design: The cavity surface must be mirror-polished (#10000 or higher diamond paste polish). Any minor scratches will be replicated on the part surface. Runners and gates should be smooth, free of stagnation points, and minimize weld marks.

Mold Cleaning: Before closing the mold, the cavity must be thoroughly wiped with a dust-free cloth, high-purity alcohol, or a dedicated mold cleaner. Any trace of dust, oil, moisture, or residue from the previous mold can cause fatal defects.

Mold Temperature Controller (Mold Temperature Control): Prepared to preheat and maintain the mold at the optimal temperature (typically 60-80°C).

Phase 2: Injection Molding Cycle (Fine Control)

Process parameters are set based on the principles of "gentle and uniform," avoiding any harsh operations that could cause material decomposition or stress.

1. Mold Closing

The mold is locked under high pressure.

2. Injection and Holding Pressure

Barrel Temperature: PMMA has a narrow processing temperature range, typically set between 210-270°C.

Too low a temperature: The melt has poor fluidity, resulting in incomplete filling, surface flow marks, and noticeable weld lines.

Too high a temperature (above 280°C): The material may decompose, yellowing, bubbles, and black specks may occur.

Injection Speed: Medium to low injection speeds are recommended.

High injection speeds can easily cause high shear stress, leading to shear overheating, localized material decomposition (producing black specks), and gas entrainment.

Slow injection speeds facilitate degassing, reducing bubbles and silver streaks, but may also make weld lines more noticeable. Finding a balance depends on the product structure. Multi-stage injection molding is typically used, with slow filling speeds in thick-walled areas to facilitate degassing and fast injection speeds in thin-walled areas.

Holding Pressure: Use medium to low holding pressures and short holding times. Excessively high holding pressures and long holding times can generate significant internal stresses, making the product susceptible to stress cracking during subsequent use. The primary purpose of holding pressure is to compensate for shrinkage, not to compact the product.

3. Cooling

Mold temperature: This is crucial and should generally be maintained between 60-80°C.

If the mold temperature is too low, the melt rapidly cools upon contact with the cold mold wall, "freezing" the molecular chains. This results in poor flow, weak weld lines, and extremely high internal stress in the product.

If the mold temperature is too high, the cooling time is prolonged, production efficiency is low, and mold sticking is likely to occur.

Cooling time: Ensure that the product is fully cooled and formed to prevent deformation during ejection.

4. Mold Opening and Ejection

PMMA is a brittle material with a high surface hardness. The ejection system must be balanced and uniform.

Avoid using sharp ejector pins. It is recommended to use large-area ejectors (strippers), push blocks, or gas-assisted ejection to prevent white spots, cracks, and obvious ejection marks.

Stage 3: Post-Processing and Inspection

Gate Removal: Carefully cut or punch out the gate and runners. Trimmed areas should be ground and polished to restore transparency and aesthetics.

Annealing (Stress Relief - Highly Recommended)

Purpose: Eliminate internal stresses generated during the injection molding process, significantly improve the product's chemical resistance (especially solvent resistance) and dimensional stability, and prevent future stress cracking.

Process: Place the product in a circulating air oven, slowly heat it to 70-80°C (10-20°C below the heat distortion temperature), hold it there for 2-4 hours, and then slowly cool it to room temperature. Rapid heating and cooling will introduce new stresses.

Surface Treatment (Optional):

Polishing: Products with minor surface blemishes or sprue marks are polished to restore a mirror finish.

Hard Coating: Spray hardening is sometimes performed to improve surface scratch resistance.

Full Inspection and Packaging

Appearance Inspection: 100% inspection is conducted under a backlit inspection light, carefully checking for any defects such as silver streaks, bubbles, black spots, scratches, shrinkage, weld marks, and impurities.

Dimensional Inspection: Use calipers, projectors, and other tools to inspect critical dimensions.

Performance Inspection: Tests such as light transmittance and haze.

Packaging: Individually isolate and package items using soft materials (such as PE bags, foam pads, or paper interlayers) to prevent scratching. Operators must wear gloves.

We are a pmma injection moulding manufacturer, providing high-quality pmma injection moulding manufacturing. As long as you want to customize/develop pmma injection moulding products, you can find us. We have professional injection mold design and mature manufacturing technology, providing you with one-stop service, from product design-mold making-product production-product packaging-product transportation, we can help you in every link. As long as you come to us, we will provide you with the ultimate service and satisfy you in terms of product quality, production time, information dialogue, etc.

Plastic Injection Mould making

Plastic molding specifications

Mold design:

Transaction process:

Mold testing:

Product packaging

Factory

We are Custom Plastic Mold factory. Our factory is plastic injection mold maker. we has 17 years of experience in professional custom plastic mold and 10 years of foreign trade experience. We are custom Plastic Mold supplier. We can provide custom Plastic Mold service. Our factory can make the Injection molded plastic parts, and the quality of the products will satisfy you.

We have more than 50 high-end machines and hundreds of engineers and designers. We can provide one-stop service, from product design - mold making - product production - product packaging - transportation. We have a complete production chain. We can meet all your requirements.

Services we provide:

Professional custom mold service, Plastic mold design and manufacturing .plastic product production, product design, mold design, blow mold customization, rotational mold customization, die-casting mold customization. 3D printing services, CNC manufacturing services, product packaging, customized packaging, shipping services.

We always adhere to the principles of quality first and time first. While providing customers with the highest quality products, try to maximize the production efficiency and shorten production time. We are proud to tell every customer that our company has not lost any customer since its establishment.If there is a problem with the product, we will seek a solution actively and take responsibility to the end.

FAQ

Q1: Are you trading company or manufacturer ?

A: We are manufacturers.

Q2. When can I get the quotation?

A: We usually quote within 2 days after we get your inquiry.

If you are very urgent, please call us or tell us in your email so that we can quote for you first.

Q3. How long is the lead-time for mold?

A: It all depends on the products' size and complexity. Normally, the lead time is 25 days.

Q4. I have no 3D drawing, how should I start the new project?

A: You can supply us a molding sample, we will help you finish the 3D drawing design.

Q5. Before shipment, how to make sure the products quality?

A: If you don't come to our factory and also don't have the third party for inspection, we will be as your inspection worker.

We will supply you a video for production process detail include process report, products size structure and surface detail, packing detail and so on.

Q6. What is your payment terms?

A: Mold Payment: 40% deposit by T/T in advance, 30% second mold payment before sending out the first trial samples, 30% mold balance after you agree the final samples.

B:Production Payment: 50% deposit in advance, 50% before sending out the final goods.

Q7: How do you make our business long-term and good relationship?

A:1. We keep good quality and competitive price to ensure our customers benefit for best quality products.

2. We respect every customer as our friend and we sincerely do business and make friends with them, no matter where they come from.